اقبال خان بونسائی

Styling bonsai tree from yamadori Lonicera collected raw material – Tree 2 – Part 4 by mikbonsai

I’m going to wire them so that these two branches like this one will move up a bit and this will move down a bit so that they become one great big pad both these branches have been widened I’m going to lower this one and raise this one lower this one slightly and we do it again by bending the wire using strength of the wire to bend it and this one’s being wrote up so they basically are looking starting to look more of a pad as opposed to being at different levels and these again and we reduced but this one I’m going to leave as is this one I think I will wire this up these two up and this one I’m going to do choir up and move it a little bit towards the camera and this one also would wire it and bring it down so the crown is more pronounced so now we will continue with this wire and this unwinding in the anti-clockwise direction and sticking very close to the branch and at a 45 degree just wire it avoiding the foliage and round it goes moving the father’s out of the way now working with the wire that of the brows that have just been wired I’m just going to bend it very very gently using the strength of the wire and then I’m gonna straighten it up from this end is starting to point downwards which I don’t want no salt quite I’m not sure dude I’ve already started wiring this branch and we continue in a clockwise direction and as it’s going to be bent in the clockwise direction so again avoiding any foliage – just wouldn’t work some of these branches are quite good and I want to retain those so except it was out of the way so positioning this where there wasn’t a pad before and so that’s that’s done that’s right nicely positioned and just shooting a few more of the branches as they are little bit too longer and we’ll see if I can do something with this one to lower this just a few centimetres perhaps an inch or so and we’ll Y trying to wire this as well now continuing to wire this pad just moving away the foliage and the branches very congested here have to use tweezers to get them out of the way some of the branches are very very fine that’ll do bend it towards the camera downwards and towards the camera so do it very very gently it’s a very thick branch and this is two things one is down and then one is towards the camera now I want to do it very very gently as they break very very brittle and they break very very easily right there we have it I’m gonna shorten this as and now shorten these branches as as bad is about this pad the lower pad is much bigger so the upper part has got to be slightly shorter and in fact we will do the same with the pads higher up so I’m going to cut this wire back to mark here and reduce this so removing paw the white partially as this part is too is too long so you’re going to reduce it to about there so reduce that to up there it was much longer and and see lots of these paths I’m going to reduce now that it’s starting to take shape this is the time to do a bit of tidy up not too sure about this branch here but we’ll leave it for now it can always be removed later because this looks quite neat and tidy and then there’s this one or a sound so I’d me I’m tempted to remove this this branch we will take it out now and it’s done then I think it looks better without that launch and this is a potential this is also a potential front and so this interesting bit here the double trunk and then fusing up here and I have removed a very big branch from here earlier that was when I first worked on it give me a quick turn and that’s the button of our front as well I will continue to grow it in this pot for a while this is a foliage that we’ve taken off today quite a lot just reveal the bonsai that was hiding unrolled all that voltage I have done fair amount and I’m pleased with the progress that I have made with this tree the this was a leader previously which I have managed to wire and turn into a small pot and this one may be the new leader basically it is no growing is thinner and also there’s a fair amount of growth up here and it’ll be far easier to form a crown with this as well and with that just finish giving it a quick turn and that’s very storage although that could be the front but on this side there’s a big contract removed a very big drought when I first started but we’ll see how it develops that’s all for now thank you watching watch more please subscribe the second account forming bonsai in Westland

Larch Bonsai Trees how to care for Larch Larix decidua (European Larch) Pruning & care Part 1

Today I’m working on a notch it has been in this training bought for a number of years now and I’ve been going there for a specific purpose there is a arch group planting in the middle of which one tree is defective and it ruins the whole composition and this tree is being drawn with intention of replacing that defective cream I’m going to start at the work marry up these donkeys are very low so these are going to remove there’s also very loud this is going to come off – very very very close together those I’m going to remove as well but create more space between the bouncer the mobile volunteers are subside as they haven’t received as much Sun the word is shortly planted at the top to allow the Sun and the light to get through to the lower branches we won’t prove too much of the lower branches just shorten about you at the top these pointers of has impaired one of them have to come off and just continue working up again responders in this to God is going to the same point someone comes off and continue working my way up here also to blog is coming from the same point for this lower one is a fellow one that comes off and just work around this is too close to the trunk or just coming out for a primary point is to close the trunk so we’ll remove this power janessa’s again make a spread crotch here that comes off and shorten this concert it’s more smaller than this comes down here and same thing singles and up here and also as a t-bar effect here I’m going to attend this one and remove perhaps remove this one and return who not sure if I’m innocent leave then primary and we’ll come back I’ve heard some people say in doubt cut it out at the trees you can’t put it back so we have a dead branch here again is coming out of very close to another branch how is remove the dead and get it in this one and it’s very congested up here so we’ll have to spin it out of it we now move to the apex and cut short these punches they’ve got very long at the top and same thing with this one here I’m going to remove this launches quite thin and not much going on zoom out a little bit madness noise I’m going to remove is quite thin and too many launches up here so this one can come off right and let’s see now please don’t use are virtually coming out of the same spot these days so I’m going to remove this one yeah all on this side you already have branches so from this side we don’t so I’m going to retain this one and remove this one here remove it right up to the trunk right sector and also turn this up into gender founded a little bit more after the data and also remove the growth rather than close the trunk if a good makes the tree look juvenile so I mean as well so there are two branches coming out will same spots up and this top one looks with dead so does remove that one or clean apart on well now have another look at the tree and see if anything else needs to be done if any dead branches or two launches too close together I’ll just give it a turn and see if there’s anything else I can spot right now this one here is sound bending downwards are shortened that a bit because get launched here and Suns coming out as kind of straight into my eyes I’ll flip and move slightly and take another look it looks okay coming up here perhaps another minute on your shelf and remove this one cannot be round and also these love goals at the straight-up trunk will take that out also too close to the trunk apex will take that out and little bit more tidying up to the gum at the apex will remove that and also this one here had fly to the top I think that as far as I want to go today and we let it go for the season before I put it in the new plant large group planting that I have and yeah this is coming along quite nicely and it’s also has a nice ah of nebari tidy up the surface root area there is a little bit of moss on the plank at the base where the surface which is hood salt we just please clean it with a toothbrush and continue the other side is a whole lot of new route not a truth serum relief cause as we are remove this accessory just can you tidy up just going to scrape plate them off say we dry the part I haven’t watered it today he’ll be able to pull them out without too much difficulty here’s the cocoa brush to wash it all off unfortunately we are playing lying and I sometimes I forget well you know here the thing and I’m sorry for that top of the pot cleaned and tidied up and take a good look at the trees before I wrap this up we have done as much tidying up as I can today so that’s cool the work for today and didn’t be left as well under the net CV enough like hope to put it into the blue planting that I have in mind for this thanks for watching and watch more please subscribe this is picnic column for big bonsai in left London until the next time now for the afterthought what do you call a nose with no body nobody knows

Nagasaki Crab Apple Bonsai Tree – Apple tree with buds, flowers and apples by mikbonsai

Hello everyone this is Iqbal Khan and today I’m going to share with you my Nagasaki crabapple tree you are looking at my Nagasaki crabapple tree it is in flower and I thought I’d share it with you not all the buds have opened but then if I wait for them to open and I get busy you could miss it so I thought I’d capture it now I will give it a quick quick turn it is a beautiful tree and it’s laden with apples. I will do another update when these flowers have turned into little apples and that’s the front this is a close-up of the flowers and will give it a turn and you can see them around the tree and that a close up of the one of the branches on the right of the tree tree Three months on from flowers to fruit the tree is now Laden that apples and I will zoom around the tree so you can see the extent of the apples and this is the left side of the tree, will gradually zoom out you can see how many apples there are and that’s the whole tree I’ll give the tree a quick turn, a full 360 and you can then see it from all directions and that is my front , that is where we started There we go as we have seen the tree is loaded with apples and a few suggestions floating around one is from a friend of mine Mani Patel if I would consider making cider and another is from Greg Hunter should I be making crab apple jelly we’ll see thanks for watching to watch more please subscribe and now for the afterthought The wife sends a text message to the husband on a on is really cold winter’s morning “the windows are totally frozen will not open” the husband replies “Gently pour warm water over it and tap the edges with your hand if that doesn’t work then gently with a hammer Fifteen minutes later the wife texts back oh no I think the laptop is completely gone you dig !

Bonsai Novice step by step beginners guide to make a Bonsai tree from nursery plant by mikbonsai

Hello again, today I have purchased a Pomegranate tree and I will be re potting it and also carrying out little bit of pruning. There isn’t a great deal to prune but never the less some of the branches are getting rather long and they need to be cut back. This is the Pomegranate tree. This is the pot I have chosen to repot the repot the pomegranate in and I think it should look OK in this. I have now managed to repot it and it now remains to be firmed in and tied in with wires. its the wire cutter and cut like so, and same thing over here. With a chopstick make sure the that there are no air pockets and will be doing this for a little while.

Now I will give it a good soaking. Very fine spray and this should do the job, I also I can also soak it from bottom up (but not necessary in this case as just repotted). I think its done the water has come through the drainage hole, so that part is done. I will now give it a quick prune and doesn’t need a great deal, but here goes Ladies and ‘Gentlemen here is the completed version. Repotted, Pruned and wired. Thank you for watching. .

Nursery plant to Fuji Cherry Bonsai Tree; KOJO-NO-MAI make instant bonsai tree -Part 2 | mikbonsai

Hello the spectral card of a petiole a very warm welcome to my bonsai channel a particularly warm welcome to my regular viewers and subscribers and if you haven’t subscribed yet I suggest you hit that subscribe button below and subscribe now and also click on the del and kick the box so that you get notifications of all my future uploads today I have got a real treat for you within the second part of the how you can make a bonsai free from energy stalk at home and I have been working on this huge charity cut off their cover and bury it in going inside you I’m now going to remove some of these other dead branches also it looks like the tree was facing that way and all the Roses on this side so I’ll have to wire some branches and spread them out a bit to improve the placement of the branches let’s all clean up these dead tranches a little stamps little bit broken Tom share the top where the moves that it looks like that this was the on the trunk divided into two here and then if you are beginning to do up here and have to make a decision as to let’s remove one of the more retain them I’ll just clean up the dead branches first and we’ll have a look at drunk dividing into three and just looking more like a bush now as opposed to a bonsai so I’ve decided to remove this little branch so we will do that now what area opens via tree up quite the therapy and now I can continue with the tuning of the Ganges and also that point is here at the top these are a couple I’ve been working with the top and start thinning out and reducing the launches will continue at that some older projects and now we have a new leader this is this relatively new leader remove all these others plant and shorten them aha that’s interesting we have another list plaintiff has 14 – – and I’m going to retain that fork the top just remove this drawer that is crossing over and perhaps reduce yes here and also reduce these branches of going south but probably why are these and then yeah why this down and also perhaps maybe while one of the targets in this side still and that don’t even say like it seeing as I move the Protestant one side so there take those out I have wired up a few branches and will now provision them and hopefully that should be it for today a little bit of movement in this launch and can you cut back to lock there in a son can go up a little bit too low and this one can be shortened that welcome there that can be shortened to there and also shortly and at law or shorten this top up there and reduce that ah clean up this cut it takes out by reducing it it will help remove the tape up that should do for now and I will let down so came using a fine mist spray to totally rocked Italy and then after it’ll be placed in a complete shade for the next three weeks I was quite funny and hot it needs protection from the Sun as powerful now folks thank you very much for watching and watch more please subscribe this little con sonic bonsai in London my wife told me to stop impersonating a flamingo I had to put my foot down so now that’s position where for you and if you are visiting and you haven’t subscribed now’s the time to six dots hit the subscribe button below and also click on the bell get the box to ensure that you to see all future notifications of my uploads and also reproduce humor at the painting

Larch Bonsai Trees how to care for Larch Larix decidua (European Larch) Pruning & care Part 1

Today I’m working on a notch it has been in this training bought for a number of years now and I’ve been going there for a specific purpose there is a arch group planting in the middle of which one tree is defective and it ruins the whole composition and this tree is being drawn with intention of replacing that defective cream I’m going to start at the work marry up these donkeys are very low so these are going to remove there’s also very loud this is going to come off – very very very close together those I’m going to remove as well but create more space between the bouncer the mobile volunteers are subside as they haven’t received as much Sun the word is shortly planted at the top to allow the Sun and the light to get through to the lower branches we won’t prove too much of the lower branches just shorten about you at the top these pointers of has impaired one of them have to come off and just continue working up again responders in this to God is going to the same point someone comes off and continue working my way up here also to blog is coming from the same point for this lower one is a fellow one that comes off and just work around this is too close to the trunk or just coming out for a primary point is to close the trunk so we’ll remove this power janessa’s again make a spread crotch here that comes off and shorten this concert it’s more smaller than this comes down here and same thing singles and up here and also as a t-bar effect here I’m going to attend this one and remove perhaps remove this one and return who not sure if I’m innocent leave then primary and we’ll come back I’ve heard some people say in doubt cut it out at the trees you can’t put it back so we have a dead branch here again is coming out of very close to another branch how is remove the dead and get it in this one and it’s very congested up here so we’ll have to spin it out of it we now move to the apex and cut short these punches they’ve got very long at the top and same thing with this one here I’m going to remove this launches quite thin and not much going on zoom out a little bit madness noise I’m going to remove is quite thin and too many launches up here so this one can come off right and let’s see now please don’t use are virtually coming out of the same spot these days so I’m going to remove this one yeah all on this side you already have branches so from this side we don’t so I’m going to retain this one and remove this one here remove it right up to the trunk right sector and also turn this up into gender founded a little bit more after the data and also remove the growth rather than close the trunk if a good makes the tree look juvenile so I mean as well so there are two branches coming out will same spots up and this top one looks with dead so does remove that one or clean apart on well now have another look at the tree and see if anything else needs to be done if any dead branches or two launches too close together I’ll just give it a turn and see if there’s anything else I can spot right now this one here is sound bending downwards are shortened that a bit because get launched here and Suns coming out as kind of straight into my eyes I’ll flip and move slightly and take another look it looks okay coming up here perhaps another minute on your shelf and remove this one cannot be round and also these love goals at the straight-up trunk will take that out also too close to the trunk apex will take that out and little bit more tidying up to the gum at the apex will remove that and also this one here had fly to the top I think that as far as I want to go today and we let it go for the season before I put it in the new plant large group planting that I have and yeah this is coming along quite nicely and it’s also has a nice ah of nebari tidy up the surface root area there is a little bit of moss on the plank at the base where the surface which is hood salt we just please clean it with a toothbrush and continue the other side is a whole lot of new route not a truth serum relief cause as we are remove this accessory just can you tidy up just going to scrape plate them off say we dry the part I haven’t watered it today he’ll be able to pull them out without too much difficulty here’s the cocoa brush to wash it all off unfortunately we are playing lying and I sometimes I forget well you know here the thing and I’m sorry for that top of the pot cleaned and tidied up and take a good look at the trees before I wrap this up we have done as much tidying up as I can today so that’s cool the work for today and didn’t be left as well under the net CV enough like hope to put it into the blue planting that I have in mind for this thanks for watching and watch more please subscribe this is picnic column for big bonsai in left London until the next time now for the afterthought what do you call a nose with no body nobody knows

Nursery Plant to Bonsai Tree – Instant Bonsai QuinceTree for under £ 10 by mikbonsai

We are looking at a quince which I have that earlier today purchased from a cotton center in Nanjing in China back at the managed to report it it’s a gift for a friend with whom I had dinner last night and I thought I’d just quickly record it is a bit primitive as I don’t have all my tools I managed to buy these butterflies as is at the market and that’s previously and the plastic is the part that it came in I haven’t quite finished reporting it and I don’t have a turntable here so we’ll have to manually turn it and we do the other side I have tidied up the Rogers and removed few of the criss-crossing Rogers will have to do for now and it started back looking free for under 10 pounds including pot and the materials the other side of the tree and from this angle we can see two rather large knobs on right-hand side of the trunk this is where the previous ruling has been done a close-up of one of the last few remaining flowers on the screens yes they do and I’ve managed to source some moss which is growing in the grounds of the flat and so trade it on out and face it in the part to enhance the appearance of the tree and the parts and the overall look of it this is the other side and close a posthumous which I’ve managed this moss in place now that’s the bonsai which was created with just a pair of scissors and some very basic material and the entire cost is around 10 pounds or just under 10 pounds not bad for a 10 pound on sight thank you for watching and much more please subscribe and now for the after thought it was this nun she was having a bath and there was a knock on the bathroom door and she said who is it the reply came it’s the blowing man and she thought herself is blowing what can you see and she said coming and the Skywalk sent and he said who Christ it’s where do you hang these blinds

Starting a bonsai tree collection from cuttings, nursery plants Part 1

Today I’m going to show you how to start a bonsai collection if you’re on a very tight budge. Hey ! it’s me it Iqbal Khan. If you have not yet subscribed to mikbonsai, then click the subscribe button and hit the bell icon to subscribe and receive notifications as I upload new videos. if you’re new and a beginner in bonsai then you have come to the right place I’m going to show you between five and seven plants first up is this cotoneaster I grew this from a cutting. I didn’t have time and I do that but I’m busy. I take cuttings and I stick them in water and this one rooted. Not every cutting that you stick in water will root but some do and that’s the easiest way of doing it. After it had rooted I planted it straight into this pot and it’s been here, I guess for a couple of years and it’s grown and I need to prune it that’s what it needs desperately and any branches which are going straight up like this one, like this one is going straight up so they have to be reduced to about two sets of leaves and I’m also going to prune this one it’s getting too long and for that reason this has to be pruned and also its called directional pruning and I will prune it with the leaf below the cut and that is the direction in which the new foliage will grow.

I’m going to cut it to about here next I’m going to prune this branch as there’s already a branch on this side I want the new branch to go in this direction so I’ll prune it to a leaf which is pointing to the left so that the new foliage will go in this direction and fill up the space here So I’ll cut it to about there and same thing with this branch here we want the growth to come outwards more to the left as there is space here so we’ll prune it to the last leaf which is pointing to the left, so this one has been pruned. So this is a sort of branch that I would stick in water and all that I have been doing in the past is remove all the leaves, nearly there, and I would just leave the leaves right at the end so leave these leaves on and then this would be stuck in water and that’s how this was grown.

Here we have a couple of parallel branches coming from virtually very… they are very close and so this is a stronger branch so I’m going to keep this and this weaker one which is slightly lower, I’m going to remove this. So we’ll prune that to there, basically where it starts from, then we prune that to there and also remove this foliage which is very close to the main trunk and it basically detract from the trunk so all this foliage is very close to the trunk will be removed and there we have it. This one I’m going to let it grow and thicken and then I’ll probably wire both of these like that, bit later in the season when the tree is going into dormancy and for now it will be put back on the bench and I’ll just remove leaves which have fallen off during my pruning and the leaves I removed from the trunk and also it needs the soil is going down and I think this is from watering.

I’ll just top up the soil and this is then ready to go back in its regular place on the benches, so there we are. I’ll just give it a quick turn and that is the first of the cuttings being made into a bonsai tree and doesn’t look half bad. It’s… it will take a little while… few years before it looks like a bonsai but it’s on its way and that’s the front for now. Next up are these cuttings the one in the terra cotta pot is a cutting which was taken from a jade plant that I pruned, stuck it in water and the full process of rooting these Jake cutting is in a in another video. I’ll include a link in the description box below and after it’s rooted it’s potted up into these terracotta pots and again I’ll leave a link below and the next phase from here is to put them into bonsai pots and that’s what you see here.

So that’s the second way of doing it again from cuttings doesn’t cost very much and these terracotta pots are about 35 pence and the start of a bonsai, This one particularly is a start of a small bonsai. There’s the larch, again this was bought for a few pounds at a local supermarket and it’s still in its original pot and I think its coming along quite nicely. I have just pruned it and removed some branches and that’s all I’ve done basically clip and grow and I will report it next spring and I will give it a quick 360 and that’s the front. This is another Cotoneaster again grown from cuttings and it’s gone absolutely crazy I have not touched it for, I think about maybe three years two or three years can’t remember and what I’m going to do is, it needs a quick tidy up so I’m going to reduce these branches quite considerably and we will use these to grow more and the ones which are going straight up like these ones, will be reduced same thing that to there and that one possibly to there, that one to there and these branches again reduce them here and here and I’m going to wire it to try and change the shape.

Dig this wire deep into the soil and then wrap it around the tree so I’m going to hold this with it with a plier and then bend the wire around the tree and from here on use my finger to support the bending of the wire, try and create a little bit more of a shape, is going in one direction so I want to try and create a little bit more of a movement as opposed to ending up with a wind swept the wire has to be wrapped around the tree at or a branch at 45° angle and making sure that we move the foliage aside like this branch and the little berry out of the way and the wire would then go in the blank space and this is how it’s done so hold the wire that’s already been wound up and move the foliage and at 45 degrees angle there we are so that’s going in and its then continued on to the next part which is moving this branch out of the way so if I just do that, move it down and holding the wired part between my thumb and finger, the forefinger and go right round that way, that parts done and repeat the process, we take it like that to there and I’m going to also remove the leaves which are on the main trunk or too close to the trunk some of them are on the primary branches but too close so they are being removed and to create a more mature look that way, up here is very busy so I’m going to tidy this up as much as I can removing too many branches close together removing those.

That’s fine, thats too low and to close, that comes off. As is this one here and looking at it from here, there are these leaves too close to the main trunk and there’s this one. Although this is quite small but it still matters that we try and follow the principles and apply the principles to irrespective of the size of the tree and some of the rules are meant to be broken but there some which you cannot get away with and the juvenile folders in the trunk is one of them. I’m going to tidy up a little bit more there are two branches here so I’m going to remove this lower one and basically it’s the branches have to be spread out and – too close doesn’t look right and again this one I’m going to remove it’s forming a ‘T’ with that one so this one will be removed and this one I’m going to shorten to about there and then I’ll wire it so that it basically, I’ll take it to the back like, like this so the tree starts becoming three dimensional.

At the moment is just front and sides so this I will wire to the back and it will go there, and up here again this is going straight up so we’ll reduce that to there to encourage new growth to go sideways and I think up here also I need to shorten it. I’m going to shorten it because they’re virtually the same sort of size, so we start to have more of an apex.

And this again will reduce it a bit more to about there. Just trying to decide what to do with this I think there’s this branch I will let it grow and we will then wire it to the back to create a back branch. I think that’s all for now. I’m just going to tidy up the pot a little bit it’s all the leaves have fallen in as I’ve pruned so that’s another Cotoneaster made from cuttings and it will go back on the benches. I’m gonna top up the soil on this one as well. In the pot it’s also the fertilizer is sitting right at the top so cover up the fertilizer. I’m giving it a little bit more of a bend in the trunk and create a little bit more interest Also I’m going to twist the trunk to create more of a, the other side of the tree. There we are, that’s a bit better.

I’ll give it a quick 360 There we are. At the next repot I will naturally need to reposition it to get the front at the moment because it was just growing and the front is usually chosen when the tree is ready for putting it in its first bonsai pot this is the recycled part that I’d used so that’s the cotoneaster the second one and the pruning that I have taken, I’ll be tidying those up and sticking them in water and hopefully they will take root as this one did and the previous one did. Next is a Chinese quince again grown from cuttings. This was taken from cuttings that came out as a result of pruning of my Chinese quince and they were stuck in water and they root quite easily and again this very very straight, this trunk it’s very thin and so this is the time to get a little bit more of a shape so wired the trunk and I’m going to sort of try and give it a little bit more of a shape and basically create more interest in the trunk and also reduce the height in the process.

Right there we are I’m not going to do very much more that should be enough just to secure the end and this basically reduced the height of the tree and that’s the tree created from cuttings. Thanks for watching that is to be continued in part 2 be sure to watch it that’s all for now. This is Iqbal Khan for mikbonsai in West London See you shortly. and now for the afterthought last week I went to see my doctor and she said what can I do for you Mr. Khan ? I explained that I was having a lot of trouble with young women and that they were all throwing themselves at me and I was having to fight them off and the doctor said what do you expect me to do ? and I said break my arms. You dig ! .

Styling bonsai tree from yamadori Lonicera collected raw material – Tree 2 – Part 4 by mikbonsai

I’m going to wire them so that these two branches like this one will move up a bit and this will move down a bit so that they become one great big pad both these branches have been widened I’m going to lower this one and raise this one lower this one slightly and we do it again by bending the wire using strength of the wire to bend it and this one’s being wrote up so they basically are looking starting to look more of a pad as opposed to being at different levels and these again and we reduced but this one I’m going to leave as is this one I think I will wire this up these two up and this one I’m going to do choir up and move it a little bit towards the camera and this one also would wire it and bring it down so the crown is more pronounced so now we will continue with this wire and this unwinding in the anti-clockwise direction and sticking very close to the branch and at a 45 degree just wire it avoiding the foliage and round it goes moving the father’s out of the way now working with the wire that of the brows that have just been wired I’m just going to bend it very very gently using the strength of the wire and then I’m gonna straighten it up from this end is starting to point downwards which I don’t want no salt quite I’m not sure dude I’ve already started wiring this branch and we continue in a clockwise direction and as it’s going to be bent in the clockwise direction so again avoiding any foliage – just wouldn’t work some of these branches are quite good and I want to retain those so except it was out of the way so positioning this where there wasn’t a pad before and so that’s that’s done that’s right nicely positioned and just shooting a few more of the branches as they are little bit too longer and we’ll see if I can do something with this one to lower this just a few centimetres perhaps an inch or so and we’ll Y trying to wire this as well now continuing to wire this pad just moving away the foliage and the branches very congested here have to use tweezers to get them out of the way some of the branches are very very fine that’ll do bend it towards the camera downwards and towards the camera so do it very very gently it’s a very thick branch and this is two things one is down and then one is towards the camera now I want to do it very very gently as they break very very brittle and they break very very easily right there we have it I’m gonna shorten this as and now shorten these branches as as bad is about this pad the lower pad is much bigger so the upper part has got to be slightly shorter and in fact we will do the same with the pads higher up so I’m going to cut this wire back to mark here and reduce this so removing paw the white partially as this part is too is too long so you’re going to reduce it to about there so reduce that to up there it was much longer and and see lots of these paths I’m going to reduce now that it’s starting to take shape this is the time to do a bit of tidy up not too sure about this branch here but we’ll leave it for now it can always be removed later because this looks quite neat and tidy and then there’s this one or a sound so I’d me I’m tempted to remove this this branch we will take it out now and it’s done then I think it looks better without that launch and this is a potential this is also a potential front and so this interesting bit here the double trunk and then fusing up here and I have removed a very big branch from here earlier that was when I first worked on it give me a quick turn and that’s the button of our front as well I will continue to grow it in this pot for a while this is a foliage that we’ve taken off today quite a lot just reveal the bonsai that was hiding unrolled all that voltage I have done fair amount and I’m pleased with the progress that I have made with this tree the this was a leader previously which I have managed to wire and turn into a small pot and this one may be the new leader basically it is no growing is thinner and also there’s a fair amount of growth up here and it’ll be far easier to form a crown with this as well and with that just finish giving it a quick turn and that’s very storage although that could be the front but on this side there’s a big contract removed a very big drought when I first started but we’ll see how it develops that’s all for now thank you watching watch more please subscribe the second account forming bonsai in Westland

Bonsai – Chinese Quince Bonsai Tree – Pruning and maintenance 1 by mikbonsai

And we’re looking at a Chinese prince it’s needs tidying up there’s all these suckers and some of the branches have got very long hello everyone I’m Nick Belkin I’m going to remove these suckers distorted I continue removing these suckers we can then start to see the actual tree so having remove these suckers you can actually now see the actual tree okay and who’s at the top it’s got very very long it’s outside the view of the camera and also here I’m just going to cut these back a bit and also remove this growth which is basically attracting from the trunk of the tree anything very close to the trunk juvenile Road should be removed again it hides the trunk and the shape this is not being very much as crying out there you could place just screwing from where this V is bang in the middle that’s no good and also remove these this clothes here don’t need any punches that know this can come off as well don’t approach here right can now start seeing the actual tree and then reduce this tree here and likewise with these branches this is going in what something back to here like that should do it as quick tidy up and you can see there’s a solid frequence hanging on and that’s all I’m going to do but yesterday except for a little bit of tidying up of the pot the outside of the pot is a bit dirty so I’m going to clean that up and the top of the pot again remove some debris and a few weeds I’ve pruned it and tidied it up a bit and also cleaned up the pot it’s beautiful when it it’s in blossom the flowers are red there’s absolutely no leaves and when it finishes flowering that’s when the leaves come out and also she has a bit of fruit this year there’s just the one and this is where I’d remove branches in the previous year again this was shortened there’s a huge branch here which I removed there’s another branch up here that was removed and there’s better fill in those taper here because that’s where the graft was and also here there’s a little bit of a problem but whereas in blossom all this becomes insignificant and I like these because of the flowers they’re absolutely stunning and you give it a quick turn and that’s back to the front thanks for watching to watch more please subscribe this is a pecan for wick bonsai in respondent there were these two cannibals walking through the jungle and this missionary on his bike and he saw these cannibals in the cannibals ocean and he jumped on his bike and started paddling furiously and one Kahneman looked at the other honest and he said look meals on wheels